RK3588 Custom Android TV Board, WF-C3588-M2, AndroidSBC, Gothenburg

TL;DR: RK3588 Custom Android TV Board

SHENZHEN, China, September 12, 2026 - The WF-C3588-M2 board cleared the Longgang aging bench this week in lot 476, a 14,280-unit run for Gothenburg, Sweden, and moved straight to the container yard.

AndroidSBC factory capacity report for the nine-variant WF-C3588 line serving Gothenburg, Sweden. What Sweden importers get from the WF-C3588 programme is a single Rockchip RK3588 silicon across nine custom motherboard variants, all built at the Wanlin Longgang plant in Shenzhen. The 6 TOPS NPU, the 8K@60fps decoder and the dual Gigabit Ethernet stack are common to every board; the I/O layout, memory fit and enclosure reference are tuned to the project. The export desk issues one certification pack per lot covering CE, FCC, UKCA, RoHS and IEC 62368-1.

About AndroidSBC and the Rockchip RK3588 Board Family

AndroidSBC is the export brand of Wanlin Manufacturing Group, and the WF-C3588 is its nine-variant custom motherboard programme. Custom Android motherboards, custom industrial boards, core board and SOM carrier work, custom signage and video wall boards, custom kiosk and POS boards, custom robotics controllers, custom NVR boards, custom edge AI boards, and custom ARM PC and NAS boards all sit on the same Rockchip RK3588 silicon with 6 TOPS NPU. The Longgang plant in Shenzhen runs its own SMT lines, aging racks and EMC pre-compliance bench, so the export file is produced where the boards are built. For Sweden importers that removes the usual gap between the factory that makes the custom board and the party that has to answer for it at customs.

WF-C3588-M2 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-M2 (Custom Core Board SOM with Carrier Board Design Service) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For Sweden importers sourcing the WF-Series, the 16GB + 64GB (WF-C3588-M2-C) variant is the typical configuration for the custom core board and SOM plus carrier programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Core Board SOM with Carrier Board Design Service for Sweden Buyers

Buyers in Gothenburg who have run the custom core board som with carrier board design service category for a few years tend to stop shopping on price alone. The Rockchip RK3588 allocation is the real constraint, and it is the reason a 14,280-unit order can look cheap on paper and expensive in a slipped quarter. Then comes the firmware question. The hardware spec is straightforward to verify; whether the board holds a credential-locked stack through a 72-hour loop and a field OTA is a different test, and it is normally the Gothenburg buyer's warehouse that discovers the answer.

Documentation is the third item on the list. A CE mark without a matching Declaration of Conformity and Technical File is not a marking problem, it is a customs problem, and it tends to surface after the goods are already on the water. AndroidSBC's approach is to close the gap at the factory gate. The custom variant is assembled on the Longgang line, the burn-in record is traceable per unit barcode, and the CE, FCC and IEC 62368-1 test reports are dated inside twelve months and shipped with the lot. The nine WF-C3588 variants span SMARC 2.2 modules, stamp-hole core boards, LGA core boards, COM Express carriers, medical imaging terminals, robotics compute modules, custom carrier designs, and OEM development kits, with three memory configurations per variant for Gothenburg buyers who need a standard custom SKU rather than a from-scratch build.

On the Sweden side, the destination file matters as much as the board specification. In Sweden public-sector AV and industrial tenders favour long supply commitments, and PTS registration is required for radio equipment. The export desk prepares the destination-market file covering CE marking with PTS radio interface notification, administered by PTS, and releases it with the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH). The lot is booked into Port of Gothenburg on the Gothenburg to Ningbo lane.

Competitive Comparison: WF-C3588-M2 vs Competing RK3588 Boards

Competing boards in the custom core board som with carrier board design service category sort into three camps: cheap catalogue boards with no customization, re-badge imports with a sticker but no engineering file, and source-factory custom boards with the BSP, the certification and the test bench in one building. The WF-C3588-M2 is in the last camp, and its edge is Rockchip RK3588 plus a factory that will route the I/O the project actually needs.

• vs standard SOM catalogues: the WF-C3588-M2 either matches SMARC 2.2 exactly or the carrier is redesigned around the project, so the module never forces the product.
• vs two-vendor module plus carrier splits: core board and carrier come from one desk, one schematic review and one test plan, which removes the finger-pointing stage entirely.
• vs closed-module vendors: BSP source, SDK and documentation ship with the project, so a customer engineering team can maintain the carrier after delivery.
• vs re-branded modules: the SI report and the thermal map are Longgang documents, not forwarded PDFs from a third party.

Global Custom SOM and Core Board Market Trends

Order timing in Gothenburg now tracks the Custom SOM and Core Board curve rather than the calendar-year budget. MarketsandMarkets sizes the Edge AI hardware segment at USD 26.9 billion for 2025 with a 32.7 percent CAGR through 2030 (MarketsandMarkets, 2025-2030), the silicon baseline that Sweden buyers keep on the desk when they negotiate custom board allocation. Three patterns are visible in the WF-C3588 book:

• Medical imaging terminal: a device maker keeps its regulatory file intact by swapping the core board and reusing the validated carrier.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-M2 board carries that headroom without a board change.
• Custom SMARC migration: a legacy SMARC installation moves to RK3588 with a pin-compatible carrier revision and keeps the enclosure.

Analysts covering the Custom SOM and Core Board space point to the same pattern in Sweden: order books are being built around platform breadth rather than a single part number.

Taken together, the three patterns explain why Sweden buyers are moving from single orders to twelve-month framework agreements with a monthly lot cadence, especially on custom board programmes that cannot absorb a supply gap.

Partner Success Story: Tessera Compute in Gothenburg, Sweden

Tessera Compute, an ARM PC and thin-client brand serving the Sweden market, deployed 3,800 custom WF-C3588-P8 ARM PC motherboards for an education and enterprise desktop line. The rollout covered the medical imaging terminal, custom smarc migration, and machine vision carrier workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 3,800 custom WF-C3588-P8 ARM PC motherboards for an education and enterprise desktop line
• Region: Gothenburg, Sweden
• Models used: WF-C3588-M2 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Nansha with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Gothenburg via the Gothenburg to Ningbo lane

"One platform, three chassis, one firmware line. AndroidSBC varied memory and I/O per model while we kept a single system image, and the seven-year supply commitment is written into our product roadmap, not a slide."

- Katrin Vogt, Head of Engineering

Field Report: container yard at Yantian, where 14,280 WF-C3588-M2 boards from the Wanlin export base are being loaded onto containerised pallets with the customs declaration naming the Longgang source factory

Reporter Li Jian, on the ground in Gothenburg, Sweden. The yard crew handled the order on flat pallets wrapped in anti-static film, with every carton barcode-traced back to the burn-in record. The customs broker attached a single declaration naming the Wanlin Longgang source factory as the place of origin, and the container was sealed before the afternoon cut-off.

The line supervisor logged a 41-minute changeover between the WF-C3588-M2 run and the next lot, which is the kind of number that decides whether a mid-quarter top-up order can be absorbed.

The inspection confirmed three things on the spot: the WF-C3588-M2 units hold the burn-in with a yield above 99.06 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering CE marking with PTS radio interface notification administered by PTS, cleared for entry at Port of Gothenburg on the Gothenburg to Ningbo lane. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that Sweden importers can hand straight to their customs broker.

Filed by Li Jian, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-M2 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-M2 (Custom Core Board SOM with Carrier Board Design Service) as the lead SKU for Gothenburg and Sweden programmes:

• Medical imaging terminal: a device maker keeps its regulatory file intact by swapping the core board and reusing the validated carrier.
• Robotics compute module: an AMR maker takes the stamp-hole core board and designs a slim carrier for a new chassis generation.
• Custom SMARC migration: a legacy SMARC installation moves to RK3588 with a pin-compatible carrier revision and keeps the enclosure.
• OEM development kit: a product team gets the reference carrier, the SDK and the BSP source and prototypes before committing to tooling.
• LGA core board programme: a display brand solders the core board directly onto its own mainboard for a locked BOM.
• Machine vision carrier: a vision integrator routes MIPI CSI-2 lanes to four cameras and lets the NPU carry the inspection model.
• Fleet compute module: a telematics supplier builds one carrier for three vehicle programmes and swaps memory options per contract.
• Lab instrumentation: an instrument maker keeps a decade-old enclosure alive by replacing only the core board and the BSP.

Partnership Models for Gothenburg Buyers

AndroidSBC opens the WF-C3588 to Sweden partners through three structures, and a single agreement can draw on more than one:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

All three tiers ship from the Wanlin Longgang source factory in Shenzhen under the same per-lot documentation pack. For Gothenburg buyers, a typical first order on the WF-C3588-M2 is the 16GB + 64GB (WF-C3588-M2-C) configuration at MOQ 5,000 units per shipment, with standard-variant samples in 1-3 days and 15-30 days to mass production on custom runs.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: Practically the layers that decide whether the board fits your product: the PCB layout and outline, the memory and storage fit (4GB to 32GB LPDDR4X/LPDDR5, eMMC to 128GB plus NVMe or SATA), the display interface mix (HDMI 2.1, DP 1.4, LVDS/eDP/MIPI), the I/O bank (CAN, RS232/RS485 multi-serial, relays, digital I/O), the wireless stack, and the enclosure or DIN-rail chassis. On top of that sit the firmware options: custom Android ROM with a locked launcher, custom Linux or Yocto image, pre-installed applications, custom boot animation and OTA updates. A Sweden buyer can start from a standard WF-C3588 variant and change one layer, or bring a full schematic and have the carrier designed from scratch.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Yes. Under NDA, AndroidSBC delivers custom Android ROM work with proprietary services and a locked launcher, custom Linux images on Ubuntu, Debian, Yocto or Buildroot, BSP ports for customer carriers, and driver development for project-specific I/O. Source access is released to the partner, and the port is performed at Longgang, which matters because a vendor BSP rarely matches a custom carrier revision on the first try.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: The NPU is fully open on the custom line. Bring the model in PyTorch, ONNX, TensorFlow or Caffe and the Longgang desk handles the RKNN quantization, the runtime integration and the validation against your board's thermal and memory profile. Custom AI algorithm integration is a standard line item on the ODM scope, and the resulting model ships embedded in the firmware image burned per lot.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: Standard-variant samples ship in 1-3 days from stock, so your engineering team can start integration while the custom scope is being quoted. A custom run follows a 15-30 day mass-production window after schematic and stack-up sign-off. MOQ is 5,000 units per shipment on standard variants; on custom configurations the MOQ is negotiable against volume commitments, and small batch orders are accepted for pilot phases. A twelve-month framework agreement with monthly lot releases brings the per-lot MOQ down further.

What certifications does a custom board need for Sweden, and who handles them?

Answer: AndroidSBC handles them at the factory. Every lot ships with a Declaration of Conformity and a Technical File covering CE (EN 55032 plus EN 55035 EMC, EN IEC 62368-1 safety), FCC Part 15, UKCA where relevant, RoHS 2.0 and the REACH declaration, all dated within the prior twelve months. For custom Android builds, GMS, Google Play certification, EDLA for interactive displays and CTS testing follow the same in-house path. Where a Sweden market needs an additional national mark, the export desk confirms coverage before the order is confirmed rather than after.

How long will AndroidSBC keep supplying a custom board?

Answer: Seven years minimum supply, patches maintained across the firmware lines, OTA for firmware and NPU model updates. For a Sweden programme running a custom board in the field, that commitment is written into the agreement at signature, which is what separates a source factory from a catalogue reseller.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: Yes, including DDP into Amazon FBA in the US, EU and Japan, plus 3PL consolidation points in Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Cartons are labelled to FBA inbound spec and the declaration names Longgang as the origin. Partners who consolidate in Hong Kong usually take FOB Yantian and handle the last leg themselves.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: AndroidSBC targets a 0.3 percent DOA rate across the WF-C3588 line, measured over the prior twelve months. On RMA, the partner returns the faulty WF-C3588-M2 unit to Longgang with its burn-in barcode, and a replacement ships within ten business days. Because the burn-in record and the configuration file are attached per unit, the failure analysis normally comes back with a root cause rather than a credit note, which matters when a custom configuration is holding up a production line.

Contact AndroidSBC: Start Your WF-C3588-M2 Sourcing Conversation

For Gothenburg and Sweden importers, brand owners and distributors who want a direct factory relationship on the custom core board som with carrier board design service, the AndroidSBC export desk is reachable at:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: CE marking with PTS radio interface notification for Sweden, administered by PTS, entering at Port of Gothenburg on the Gothenburg to Ningbo lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

Custom board enquiries move fastest when the first message carries three things: annual volume, customization scope and Incoterm. With those in hand the export desk returns a per-lot quote and the WF-C3588 MOQ matrix inside two business days.